BeLight™ Ultra-Low Transmission-Loss Thermoplastic Film
    Publish time 2026-10-29 15:49    
BeLight™ Ultra-Low Transmission-Loss Thermoplastic Film

Affiliation: Apex — Authorized Distributor of Mitsubishi Chemical

Meta description: Mitsubishi Chemical BeLight™ ultra-low transmission-loss thermoplastic film — Df<0.001@28GHz, water absorption <0.1%, copper peel strength >20 N/10 mm, UV-laser processable, heat resistance up to 260°C, VTM-0 flame retardancy. Designed for high-frequency high-speed circuit substrates, core materials, and flexible flat cable (FFC), with transmission loss comparable to fluoropolymers.

Models: BeLight™ SNL, ST, SDL, TT, U, UD types


 

BeLight™ ultra-low transmission-loss thermoplastic film product overview


Core Value

BeLight™ — ultra-low transmission-loss film with high copper-foil adhesion, directly targeting high-frequency signal attenuation

· Ultra-low dielectric loss: Df < 0.001 @28 GHz, transmission loss comparable to fluoropolymer (PTFE).

· Low water absorption: <0.1%, stable high-frequency electrical performance.

· High copper-foil adhesion: Peel strength to copper foil >20 N/10 mm (SNL/ST types), overcoming the weak adhesion of fluoropolymers/COP.

· UV-laser processable: Supports UV laser patterning for easier circuit formation.

· Rich model lineup: SNL (laser-processable + VTM-0 flame retardant), ST (transparent + weatherable), U/UD (low CTE, heat-resistant), and more.

· Dual FFC use: Can serve as both FFC adhesive and substrate, lowering the dielectric constant of the insulation.


Product Description

BeLight™ is an ultra-low transmission-loss thermoplastic film from Mitsubishi Chemical, targeting high-frequency high-speed circuit substrates and flexible flat cable (FFC). It achieves ultra-low dielectric loss on par with fluoropolymers while solving the weaknesses of fluorinated materials — low copper-foil adhesion, inability to laser-process, and low elongation at break.

1. Working Principle & Technical Breakthrough

When high-frequency signals transmit through an insulating material, dielectric constant Dk and dielectric loss Df directly determine signal attenuation. Through materials design, BeLight™ brings Df down to the 0.0003–0.0005 @28 GHz range, with 40 GHz transmission loss on par with LCP and PTFE; surface/formulation design simultaneously delivers high copper-foil adhesion (>20 N/10 mm) and UV-laser processability.

2. Performance & Precision Parameters

· Dielectric: Dk 2.2 @28 GHz (SNL/ST/SDL/TT/U types), Df 0.0003–0.0015 (by grade).

· Copper-foil peel strength: SNL/ST >20 N/10 mm; U-type 8.4, UD-type 6.4 N/10 mm.

· Heat resistance: TT/UD types DMA heat resistance 260°C.

· Flame retardancy: SNL type VTM-0.

· Transparency / weatherability: ST type total transmittance 93%, haze 1%.

· Target thickness: 100, 75, 50, 25 μm; roll width <1300 mm.


 

BeLight™ development model performance comparison table


3. Materials & Product Applicability

U-type (no inorganic filler): melting point 271°C, Tg 112°C, CTE 90 ppm/°C, Dk 2.4, Df 0.0004, water absorption <0.1%, tensile elongation 50%; UD-type (glass-fabric-reinforced): CTE 14 ppm/°C, Dk 2.9, Df 0.0015, tensile elongation 7%. Target applications include circuit substrates and core materials.

4. Core Value & Application Benefits

In FFC, BeLight™ can serve as both adhesive (S-type, hot-melt) and substrate (U-type, PET, etc.), suppressing high-frequency signal attenuation by lowering the dielectric constant of the insulation (adhesive + substrate). Board traces can also be replaced by FFC, reducing low-Dk substrate usage and increasing design freedom.


 

BeLight™ application example: flexible flat cable (FFC)

 

BeLight™ expected FFC scenarios: high-speed transmission and loss reduction


Key Advantages

(I) Fluoropolymer-Level Low Loss + High Copper-Foil Adhesion

BeLight™ offers 40 GHz transmission loss on par with LCP and PTFE while overcoming fluoropolymer/COP weaknesses — low copper-foil adhesion (<3 N/10 mm), inability to laser-process, and low elongation. Copper-foil adhesion reaches >20 N/10 mm, and UV-laser processing is supported, making high-frequency circuits and FFC easier to fabricate.

(II) Model Matrix Covers Diverse Requirements

Model

Features

Heat resistance °C (DMA)

Dk @28G

Df @28G

Copper peel N/10mm

SNL

Laser-processable + flame retardant

150

2.2

0.0004

>20

ST

Transparent + weatherable

150

2.2

0.0003

>20

SDL

Laser-processable

150

2.8

0.0005

>10

TT

Transparent + reflow-resistant

220

2.2

0.0006

8

U

Reflow-resistant + low CTE

260

2.4

0.0004

>10

UD

Reflow-resistant + low CTE + heat-resistant

260

2.9

0.0015

>10

Note: Values are representative measured examples, not guaranteed values.

(III) Dual FFC Use, Lowering Insulation Loss

Using BeLight™ as both FFC adhesive and substrate significantly reduces transmission loss at equal length compared with ordinary FFC (PET substrate + polyester adhesive), supporting high-frequency high-speed transmission.


Technical Specifications

Item

Parameter

Product type

Ultra-low transmission-loss thermoplastic film

Models

SNL, ST, SDL, TT, U, UD types

Target thickness

100, 75, 50, 25 μm

Roll width

<1300 mm

Dielectric constant Dk (28 GHz)

2.2 (SNL/ST/SDL/TT/U); 2.4 (U-type measured); 2.9 (UD-type)

Dielectric loss Df (28 GHz)

0.0003–0.0015 (by grade)

Water absorption

<0.1%

Copper-foil peel strength

>20 N/10 mm (SNL/ST); U-type 8.4, UD-type 6.4 N/10 mm

Heat resistance

Up to 260°C (TT/UD types, DMA)

Flame retardancy

VTM-0 (SNL type)

Transparency / weatherability

ST type total transmittance 93% / haze 1%

Laser processing

YAG, 360 nm processable (SNL/SDL types)

Note: The above data are representative measured values from Mitsubishi Chemical product literature and are not guaranteed values.


Applications

High-Frequency Communications & High-Speed Circuits

· 5G / high-frequency high-speed circuit substrates and core materials.

· High-frequency copper-clad laminate substrates with high copper-foil adhesion.

Flexible Flat Cable (FFC)

· FFC adhesive and substrate, lowering the dielectric constant of the insulation.

· High-speed FFC jumpers, replacing partial board traces.

Others

· Electronic insulation and thermal-lamination applications requiring low dielectric constant.

· High-frequency components requiring VTM-0 flame retardancy or transparent weatherability.


FAQ

Q: What dielectric performance level does BeLight™ offer? 

A: BeLight™ dielectric loss Df can be as low as 0.0003–0.0004 @28 GHz, with 40 GHz transmission loss on par with fluoropolymers such as LCP and PTFE — an ultra-low transmission-loss thermoplastic film.


Q: What practical advantages does BeLight™ offer over PTFE/LCP? 

A: While maintaining low loss, it offers high copper-foil adhesion (>20 N/10 mm, vs fluoropolymer/COP typically <3 N/10 mm), UV-laser processability, and high elongation, making high-frequency circuits and FFC easier to fabricate.


Q: How is BeLight™ used in FFC? 

A: It can serve as both FFC adhesive (e.g., S-type, hot-melt) and substrate (e.g., U-type), lowering the dielectric constant and loss of the insulation (adhesive + substrate) to reduce high-frequency transmission loss.


Q: Which models are available and how do I select? 

A: SNL (laser-processable + VTM-0), ST (transparent + weatherable), SDL (laser-processable), TT (reflow-resistant 220°C), U/UD (reflow-resistant 260°C, low CTE; UD includes glass fabric). Select by heat resistance, flame retardancy, transparency, and CTE requirements.


Q: What are the thickness and width specs? 

A: Target thickness 100/75/50/25 μm, roll width <1300 mm; please refer to the formal specification sheet for details.




Get a Quote / Contact Us

Apex — Authorized Distributor of Mitsubishi Chemical

Email: qhyz@apexe.net